MODEL VCBS-1/8-TX- 6"X 5'- VERTICAL CONVEYORIZED BAND SEALING SYSTEM

Completely Validatable Seals

• USDA Approved Vertical Rotary Band Sealing System with Bag Top Trimmer and Lower Carry Synchronized Conveyor.
• Supplied with Lower Carry Belts and interfaced Variable Speed Conveyor, 6" wide x 5' long, with fully adjustable stainless steel Guide Rails. Adjustable height Sealing Assembly Floor Stand with crank handle and Vacuum System for trim scrap removal is standard.
• This continuous band sealer will seal and trim Tyvek®, Foil, Polyethylene, Polypropylene, Nylon, Coextrusions, polylaminates and poly-coated paper materials.
• Smokeless and odorless sealing and trimming.
• Variable speeds up to 540 inches per minute (45 fpm) with ultra-quiet gear motor.
• Quality seals of 1/8", 1/4" or 3/8" wide are achieved through the use of special heavy duty wear-resistant laminated Teflon bands.
• Digital Temperature Control with PID Autotune maintains consistent heat and assures quality hermetic seals.
• Unit is designed with 5" long heating zone and 5" long cooling zone for greater flexibility in product sealing of difficult materials with temperatures up to 500 degrees Fahrenheit.
• Hard Chrome plated sealing bars followed by Nickel plated cooling bars allow for maximum wear resistance.
• Electrical 110 VAC 10 amps/ 60 Cycle. No compressed air required.
• Optional Casters (shown) for easy positioning are available upon request.
• Optional Infeed Conveyor supports heavy or bulky packages for final seal and trim is available upon request.
• System available mounted on 4' high adjustable floor stand, may complement your existing conveyoring equipment by positioning the Sealing System over it and adjusting the variable speed drive to match. Model VBS-1/8TX is available upon request.
• Custom configurations are available, inquire with our Sales Department with your application.

ALL AIR HCBS & BAGGER

Simple to Install, Easy to Use, Durable Construction, Uses a Variety of Films. The USDA approved HCBS Band Sealer and All Air Bagger Model SBP-SS-AA-16 Bag Loader offer the following:

• The HCBS offers state of the art sealing.
• It produces a tight secure sealed bag using Polyolefin and PVC shrink bags that require precise temperature controls to create a consistently tight package every time.
• It works equally well on a variety of films such as Polyethylene, Polypropylene, Polymylar and Coextrustions, that require precise temperature controls to create a consistently tight package every time.
• The Bag Loader is designed for maximum flexibility and ease of use.
• The air driven loader arms allow trayed product to slide easily into the bag.

VBS-DH-3/8-10-V BAND SEALER

Complete, Visible Validation on Continuous Band Sealer for Medical Pouches

• USDA approved rotary band sealing system.
• Unit is designed with 10" long heating zone, and 10" long cooling zone for greater flexibility in product sealing of difficult materials with temperatures up to 500 degrees +/-2 degrees Fahrenheit.
• Temperature, speed control and cooling bar pressure can be validated.
• Single line embosing code available.
• Extra sealing capacity allows speeds up to 60' per minute with constant secure seals of 1/4" or 3/8" wide without bag top trimmer.
• Designed to seal Nylon, Polyethylene, Polypropylene, Laminates, Tyvek/Polymylar and Foil.
• Self contained compressed air, 110V, 1 Phase, 60 Cycle. No external air required.
• Seals are achieved through the use of special heavy duty wear-resistant laminated Teflon bands.
• Quad digital temperature controls maintain consistent heat and assures quality hermetic seals. Heat is generated from rear and front heaters or one set only as required using a simple on/off switch. Individual heating assemblies can be regulated due to Quad controls.
• Easy quick changeover and cleaning of the Teflon Bands due to instant pressure release on bands placed in an open position. Uniform pressure on all sealing and cooling surfaces creates consistent quality validatable seals. Gauges are easy to read and highly visible.
• Mounted on a heavy duty floor model adjustable stand with crank handle and can be ordered in the vertical or horizontal position. Vertical unit can be positioned over existing lower carry conveyor.
• Chassis sealing assembly construction of stainless steel shafting throughout and anodized aluminum assures longevity of use. Chrome plated sealing assemblies reduce wear.
• Dual Element Thermocouple: Each thermocouple has two junctions, one for the temperature controller and one for temperature verification, ports supplied.

TBS PORTABLE BAND SEALER

Portable USDA approved rotary table model sealing system renders 3/8" wide hermetic seal without trim. Designed on swivel base for sealing from vertical to 45 degrees position.

• Materials : PE, PP, Kraft/PE, Tyvek, Polymylar, Foil/PE, Cryovac, Coextrusions, Polylaminates, Military Specs, Nylon.
• Speeds of up to 45 feet per minute, depending on bag thickness and material.
• Digital precise temperature controller up to 500 degrees plus or minus 2 degrees.
• Chrome plated sealing assembly and cooling section.
• No Compressed air required.
• 110 V, 1 phase, 60 Cycle.
• Stainless Steel Shafting throughout.

Designed to Seal Tyvek/Mylar, Nylon, Polyethylene, Polypropylene, Laminates, Kraft/PE and Foil

• Seals are achieved through the use of special heavy duty wear-resistant laminated Teflon bands.
• Chrome plated sealing assemblies followed by Nickel plated cooling sections reduce wear of assemblies and increases lifespan of machinery.
• Temperature, speed, sealing and cooling bar pressure are validated. Highly recommended for the sealing of Medical Devices in pouches.
• With the new model TBS 3/8-V seal pressure is achieved through the use of compressed air- external clean air is required.
• Easy and quick changeover and cleaning of the Teflon bands is possible due to the instant pressure release of the seal bars on the bands when placed in an open position.
• Uniform pressure on all sealing and cooling surfaces creates consistent quality validatable seals.
• Gauges are easy to read and highly visible.
• Single line embossing coder for product marking available.
• Two digital temperature closed loop controls maintain consistent heat and assure quality hermetic seals.
• Heat is generated from rear and front heaters or one set only as required using a simple on/off switch.
• Individual heating assemblies can be regulated because of separate controls.
• Stainless steel chassis and anodized aluminum assures longevity of use.

MODEL VFFS - PACKMASTER POUCHER/BAGGER

Compact Vertical Form, Fill and Seal Bagging System

• Package Production Applications: For a wide variety of products and industries such as Automotive, Candy, Cosmetics, Disposables, Electronics, Food, Garden, Hardware, Stationery, Toys,and non-sterile Medical, Hospital, & Pharmaceutical products.
• Labor Reduction: Packmaster reduces labor costs when compared to hand bagging.
• Material Savings: Using standard centerfolded film when compared to pre-made bags or special perforated bags on a roll.
• Easy Operation: PLC with Keypad Display Controlled and PID Autotune Control of sealing temperature ensures easy set-up, quality seals and consistent performance.
• Smokeless and Odorless Sealing Design: Proprietary seal blade and coating design.
• Speeds: Up to 30 packages per minute in automatic mode.
• Designed to Seal Materials: Center Folded Polyethylene, LLDPE, Shrink films, either A or B Wind plain and/or preprinted.
• Interchangeable Jaw System: Designed for rapid product changeover from Poucher to Bagger styles in 20 minutes or less.
• Pouch/Bag Sizes: Ranging from a maximum 12" horizontal x 8" vertical down to 2" x 1".
• Jaw Opening: Up to 3" available on pouch pack style jaw and up to 6" jaw opening on a standard "L" type jaw.
• Dimensions: 26" wide, 36" deep, 55" high.
• Electrical: 110 VAC 5 amps/ 60 cycles.
• Air: 80 PSI.
• Available Options: Print Registration for printed film, Adjustable Film Web Guides and/or Integrated Infeedand Outfeeds systems for a complete Turnkey sealing system.

SPEEDY BAGGER & DROP SEALER (GRAVITY SEALER)

Speedy Bag Packager is a bag loader that blows open pre-made bags on a wicket. Available seals: Bead trim, Impulse trim, Hot bar seal and trim.

• Construction: Painted steel with stainless steel contact surfaces.
• USDA approved models available.
• Vertical filling models available.
• Air supply-Self contained adjustable air generator- retractable for easy cleaning 3 year warranty.
• Production Speeds Up to 24 bags per minute-3 x faster when compared to hand bagging operations.
• Bag reservoir: Holds up to 300 bags, completely adjustable with parallel action.
• Interfaces with Drop Sealer and HCBS models sealers and can be used with vertical band sealers (VCBS models).
  
• Loaded bag is placed into drop sealer chamber.
• Jaw drops down and seals/trims bag.
• Can be operated in manual or automatic mode.
• Quick and accurate length and width adjustments take seconds due to upper and lower adjustable stainless steel side guides.
• Stainless steel contact surfaces. Compressed air is required.
• 110V, 1 phase, 60 cycle, (220V available)
• Safeguard device available, adjustable compression plate available to remove excess air before sealing.

MODEL ATS - TABLE SEALERS ATS (AIR OPERATED TABLE SEALERS)

• Available Models: ATS-16 thru 24, ATS-SS-16 thru 24, ATS-SS-l6-PI', ATS-IMP-1 /8T- 16 thru 24, ATS-SS-IMP 5/16-16 thru 24, ATS-IMP-1 /4 + 1/4T-16 thru 24, ATS-HB-1+1-16 thru 24.
• Available Seals: (respective to models) Bead trim seal, Smokeless and Odorless bead trim seal, 1/8"- 1/4" seal and trim, 1/8" Smokeless and Odorless seal & trim, upper and lower 1/4" heavy duty seal & trim, upper & lower 1" heavy duty seal only.
• ATS models require compressed air.
• Electrical: 110 V, 1 phase, 60 cycle (220V available)
• Size bags: 2"-24" wide, other custom models up to 42" wide.
• Materials: Polyethylene, Polypropylene (without angel hairs) Cellophane, Barrier, Tyvek, Coextrusions, Laminates, Military Specs.
• Accurate heat controls.
• Preheat design on Smokeless and Odorless models means no warm up time is required.
• Complete with adjustable front feeder tray with scrap removal & scrap accumulator.
• Safeguard device available.
• Contour seals available.